The Straight Dope

Go Back   Straight Dope Message Board > Main > General Questions

Reply
 
Thread Tools Display Modes
  #1  
Old 10-26-2010, 12:20 PM
dzero dzero is offline
Member
 
Join Date: Aug 2010
What's the best way to cut wood veneer?

The cabinets in my kitchen have what I think is a cherry veneer. I have no idea what the wood under that is.

I needed to cut about 3/8ths of an inch off the skirt of one cabinet to make room for a countertop dishwasher. I always wanted a dishwasher but had no intention of doing a complete remodel on my 50 year old kitchen in order to get one.

Anyway, as you probably know, the problem with wood veneer is that it cracks and splinters more easily than an egg shell. I figured that using a circular or reciprocating saw would be a receipt for disaster (look for my new disaster cook book from Harper-Collins later this year - kidding). So I had what I thought at the time was an absolutely brilliant idea. I'd mark off the area to be trimmed and I would drill about a hundred or so holes along that line. The idea was to create a row of perforations through both the veneer and the underlying wood. Then I would take a wood chisel and neatly slice off the bottom 3/8th's.

Well, it has worked reasonably well so far. I started with the side of the cabinet where the wood, apparently, is quite thin - maybe 1/8 - 1/4 inch. The door however is proving more challenging. The wood there is a bit over 3/8th's thick and the perforations don't seem to be giving me much of an advantage.

At this point I suppose I'm committed - or at least should be perhaps (???) - and I was wondering if there isn't an easier and possibly neater way to cut wood veneer.
Reply With Quote
Advertisements  
  #2  
Old 10-26-2010, 12:38 PM
Rain Soaked Rain Soaked is offline
Guest
 
Join Date: Oct 2006
I've put a strip of painters tape along the line I wanted to cut and used a jig saw with a very fine blade. The tape keeps the counter top from splintering.
Reply With Quote
  #3  
Old 10-26-2010, 12:41 PM
Kevbo Kevbo is offline
Guest
 
Join Date: May 2005
pre-cut through the veneer with a utility or X-acto knife. Make sure the saw blade stays just to the scrap side of the knife cut.

Learned this trick from a guy who did picture framing.
Reply With Quote
  #4  
Old 10-26-2010, 12:44 PM
awldune awldune is offline
Guest
 
Join Date: Mar 1999
What they said. I also wonder if a Dremel cutoff wheel would work, but that would be more tedious than the jigsaw option.
Reply With Quote
  #5  
Old 10-26-2010, 12:47 PM
jz78817 jz78817 is offline
Guest
 
Join Date: Aug 2010
a dremel would probably cause the wood to burn. I've used the painter's tape trick a couple of times which seemed to work.
Reply With Quote
  #6  
Old 10-26-2010, 12:53 PM
CookingWithGas CookingWithGas is offline
Charter Member
 
Join Date: Mar 1999
Location: Tysons Corner, VA, USA
Posts: 9,776
Quote:
Originally Posted by Kevbo View Post
pre-cut through the veneer with a utility or X-acto knife. Make sure the saw blade stays just to the scrap side of the knife cut.

Learned this trick from a guy who did picture framing.
This is my suggestion as well. Veneer is thin enough to cut with a utility knife or razor blade. Clamp a metal straightedge on as a guide if practical. I haven't done exactly what you're trying to do but I did work with some veneer once and it is thin.
Reply With Quote
  #7  
Old 10-26-2010, 01:20 PM
crazyjoe crazyjoe is offline
Guest
 
Join Date: Dec 2004
Clamping a metal straightedge is likely to scratch the veneer. I'd go with painter's tape, I have seen that trick before. Also a trim-cutting blade (on a circular saw or jigsaw) will give much less chance of splitting the veneer since it has much finer teeth.
Reply With Quote
  #8  
Old 10-26-2010, 01:46 PM
dzero dzero is offline
Member
 
Join Date: Aug 2010
Thanks for all of the great ideas.

Something I didn't mention but probably should have is that I'm doing this in situ as it were. I didn't have much of a choice with the side wall of the cabinet, but for the door, I could have taken that down. The way it looks now, I might have to do that anyway. I think I have some "frog tape" (???) - I think that is basically painters tape.
Reply With Quote
  #9  
Old 10-26-2010, 01:50 PM
Rain Soaked Rain Soaked is offline
Guest
 
Join Date: Oct 2006
Quote:
Originally Posted by dzero View Post
I think I have some "frog tape" (???) - I think that is basically painters tape.
Yes, that is the same thing. You just want a tape that will not leave a sticky residue when you peel it of.
Reply With Quote
  #10  
Old 10-26-2010, 01:53 PM
Giles Giles is offline
Charter Member
 
Join Date: Apr 2004
Location: Newcastle NSW
Posts: 12,004
How about combining the methods?:
(1) Put masking tape on the veneer;
(2) Clamp a steel rule on top of the masking tape (where it won't scratch the veneer;
(3) Cut the veneer along the line with a knife;
(4) Remove the steel rule;
(5) Cut with a jigsaw;
(6) Remove the masking tape.
Reply With Quote
Reply



Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is Off
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:19 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.

Send questions for Cecil Adams to: cecil@chicagoreader.com

Send comments about this website to: webmaster@straightdope.com

Terms of Use / Privacy Policy

Advertise on the Straight Dope!
(Your direct line to thousands of the smartest, hippest people on the planet, plus a few total dipsticks.)

Publishers - interested in subscribing to the Straight Dope?
Write to: sdsubscriptions@chicagoreader.com.

Copyright 2013 Sun-Times Media, LLC.