# How would you stop the oil leak?

**URL:** <https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367>\
**Category:** In My Humble Opinion\
**Created:** [June 24, 2010, 3:47pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367 "2010-06-24T15:47:54Z")\
**Posts on this page:** 20\
**Page:** 2

<div class="post-metadata">

**Author:** ![Terraplane](https://avatars.discourse-cdn.com/v4/letter/t/74df32/32.png) [@Terraplane](https://boards.straightdope.com/u/Terraplane)\
**Post date:** [June 24, 2010, 7:51pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/21 "2010-06-24T19:51:04Z")

</div>

> [@billfish678](#):
>
> I suspect that number is misleading.
> 
> Remember the pressure of the water a mile deep is pretty high. Approximately 2300 PSI. If the well is at 2310, its only a 10 PSI difference. The 2300 part is irrelevant to the flow rate or the difficulty in stopping it.
> 
> Looking at the videos, it doesnt look to me like the well pressure is “barrel of gun” higher than the surrounding water. Though I dont know what it actually is. To me, it looks more like “big fire hose” higher pressure.

The lowest estimate I’ve seen, from an interview with Admiral Allen, is around 3500 PSI at the bottom of the BoP. If so, that’s about 1200 PSI flow rate out of the top\*, or anywhere from 4 to 12 times the pressure of a fire hose, though in this case the ‘hose’ is 21" across. Nowhere near bullet pressure really but I don’t think I’d want to stick my hand over it.

\*I think that’s how it works, anyway.

> [@Disheavel](#):
>
> I think putting 3-4 anchors (large concrete blocks with flukes) around the pipe to give some counterpressure capability. From there I would erect a tripod platform with a hydraulic ram to push a big rubber (or steel) stopper into the well head. They keep doing things from moving platforms which just seems to be adding to the difficulty.

The well contains a two mile column of highly pressurized liquid moving rapidly upward. If you jam something into the well head the pipe is likely to explode.

> [@Hampshire](#):
>
> Why not lower a massive bell or dome over it that has a few dozen hydraulicly controlled ports. Lower it down with all the ports in the open position so the oil can siphon through. Close one, attach a pipe, open it and suck oil. Close another, attach another pipe, open it and suck oil. Repeat another 22 times.

Isn’t this similar to what they tried to do with the containment dome? That failed when [methane hydrate crystals](http://en.wikipedia.org/wiki/Methane_clathrate) formed and clogged the thing. I think it’s important that the oil and gas stay under pressure all the way up the pipe.

From the wiki link…

> [@](#):
>
> ethane clathrates (hydrates) are also commonly formed during natural gas production operations, when liquid water is condensed in the presence of methane at high pressure. It is known that larger hydrocarbon molecules such as ethane and propane can also form hydrates, although as the molecule length increases (butanes, pentanes), they cannot fit into the water cage structure and tend to destabilise the formation of hydrates.

---

<div class="post-metadata">

**Author:** ![Magiver](https://avatars.discourse-cdn.com/v4/letter/m/4491bb/32.png) [@Magiver](https://boards.straightdope.com/u/Magiver)\
**Post date:** [June 24, 2010, 9:04pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/22 "2010-06-24T21:04:55Z")

</div>

For starters I would have cut the riser differently. Anyone who ever cut a tree down knew the 2nd cut was going to bind because of the weight (the riser was suspended in a sling after the first cut). They should have cut the 2nd at the bend (with shear cutters) and made a 3rd and final cut below that with the loop cutter. Instead of an outer mating cap I would have used an inner matting cap designed to round the hole straight and promote a steel-on-steel or copper on steel seal. From there I would attempt a chemical weld.

---

<div class="post-metadata">

**Author:** ![billfish678](https://avatars.discourse-cdn.com/v4/letter/b/7bcc69/32.png) [@billfish678](https://boards.straightdope.com/u/billfish678)\
**Post date:** [June 24, 2010, 9:31pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/23 "2010-06-24T21:31:18Z")

</div>

Does anybody know the current best estimate of the hourly/daily flow rate?

---

<div class="post-metadata">

**Author:** ![Markxxx](https://avatars.discourse-cdn.com/v4/letter/m/5daacb/32.png) [@Markxxx](https://boards.straightdope.com/u/Markxxx)\
**Post date:** [June 24, 2010, 10:23pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/24 "2010-06-24T22:23:20Z")

</div>

I know all about these things, since I’ve seen every all of t_he Three Stooges_ shorts.

Generally the best thing to do in cases like these is to use Curly or sometimes Joe as a cork.

Curly: Hey Look guys I’m a successful cork

---

<div class="post-metadata">

**Author:** ![AlsoNamedBort](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/alsonamedbort/32/3213_2.png) [@AlsoNamedBort](https://boards.straightdope.com/u/AlsoNamedBort)\
**Post date:** [June 24, 2010, 10:31pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/25 "2010-06-24T22:31:41Z")

</div>

Just stick someone slightly fatter than Augustus Gloop in the pipe.

---

<div class="post-metadata">

**Author:** ![figure9](https://avatars.discourse-cdn.com/v4/letter/f/f0a364/32.png) [@figure9](https://boards.straightdope.com/u/figure9)\
**Post date:** [June 24, 2010, 10:33pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/26 "2010-06-24T22:33:37Z")

</div>

Sumerian-Cobalt magnets. Shoot them in bunches down the pipe. First they stick to the sides of the pipe then they stick to each other. Problem solved. As a plus all the magnets I’ve torn out of hard-drives become more valuable.

---

<div class="post-metadata">

**Author:** ![DMark](https://avatars.discourse-cdn.com/v4/letter/d/e68b1a/32.png) [@DMark](https://boards.straightdope.com/u/DMark)\
**Post date:** [June 25, 2010, 1:38am UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/27 "2010-06-25T01:38:48Z")

</div>

Duct tape.

---

<div class="post-metadata">

**Author:** ![El\_Kabong](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/el_kabong/32/496_2.png) [@El\_Kabong](https://boards.straightdope.com/u/El_Kabong)\
**Post date:** [June 25, 2010, 3:44am UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/28 "2010-06-25T03:44:25Z")

</div>

I’d drill a couple of relief wells, then inject cement when they manage to intercept the blown-out well bore.

I really have no idea why BP isn’t trying something like that. 😉

Meanwhile, concerning the estimates being thrown around: anyone who is basing the eventual total spill volume on the total estimated reservoir volume is talking out their ass and hasn’t a clue how reservoirs work. I doubt there is an oil or gas reservoir anywhere in the world where more than 20 percent or so of the oil in place flows to surface without assistance. Even with enhanced recovery technigues, most reservoirs [only give up 30 to 60 percent](http://en.wikipedia.org/wiki/Extraction_of_petroleum) of their hydrocarbons in place. Likewise, for a reservoir of the size and extent of Macondo, it is highly unlikely a single wellbore could draw fluid from all parts of the reservoir.

I’d say take the estimated reservoir volume and assume five percent or less of that as a ballpark figure.

Note: I am in no way dismissing the extent and seriousness of this disaster, just trying to keep things realistic.

---

<div class="post-metadata">

**Author:** ![Shirley\_Ujest](https://avatars.discourse-cdn.com/v4/letter/s/45deac/32.png) [@Shirley\_Ujest](https://boards.straightdope.com/u/Shirley_Ujest)\
**Post date:** [June 25, 2010, 12:29pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/29 "2010-06-25T12:29:13Z")

</div>

Duct Tape & Augustus Gloop.  
[Costner’s](http://blogs.chron.com/newswatchenergy/archives/2010/06/bp_says_kevin_c.html) Machine has gotten the greenlight from BP.

One part of me hopes this works, the deeper darker cynical side of me wonders if BP is throwing money after this to divert all the bad press until something better comes along.

---

<div class="post-metadata">

**Author:** ![Nzinga\_Seated](https://avatars.discourse-cdn.com/v4/letter/n/b5ac83/32.png) [@Nzinga\_Seated](https://boards.straightdope.com/u/Nzinga_Seated)\
**Post date:** [June 25, 2010, 1:00pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/30 "2010-06-25T13:00:41Z")

</div>

I say we fight oil with oil.

---

<div class="post-metadata">

**Author:** ![Kiber](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/kiber/32/317_2.png) [@Kiber](https://boards.straightdope.com/u/Kiber)\
**Post date:** [June 25, 2010, 1:18pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/31 "2010-06-25T13:18:22Z")

</div>

Chuck Norris. HE could stop it.

---

<div class="post-metadata">

**Author:** ![Superhal](https://avatars.discourse-cdn.com/v4/letter/s/b4bc9f/32.png) [@Superhal](https://boards.straightdope.com/u/Superhal)\
**Post date:** [June 25, 2010, 1:31pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/32 "2010-06-25T13:31:56Z")

</div>

Dump all the SUV’s from the Cash for Clunkers program into the gulf. They’re like a giant oil sponge.

---

<div class="post-metadata">

**Author:** ![UncleRojelio](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/unclerojelio/32/3160_2.png) [@UncleRojelio](https://boards.straightdope.com/u/UncleRojelio)\
**Post date:** [June 25, 2010, 1:53pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/33 "2010-06-25T13:53:30Z")

</div>

> [@Superhal](#):
>
> Dump all the SUV’s from the Cash for Clunkers program into the gulf. They’re like a giant oil sponge.

I dunno, I think the Jeep that I traded in leaked oil faster than that well does.

---

<div class="post-metadata">

**Author:** ![blindboyard](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/blindboyard/32/2833_2.png) [@blindboyard](https://boards.straightdope.com/u/blindboyard)\
**Post date:** [June 25, 2010, 2:17pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/34 "2010-06-25T14:17:34Z")

</div>

Easy. Nuke it. Nukes make things better, everyone knows that.

[http://www.crunchgear.com/2010/05/05/russian-advice-nuke-the-oil-spill-thatll-fix-it/](http://www.crunchgear.com/2010/05/05/russian-advice-nuke-the-oil-spill-thatll-fix-it/)

---

<div class="post-metadata">

**Author:** ![Chessic\_Sense](https://avatars.discourse-cdn.com/v4/letter/c/7c8e57/32.png) [@Chessic\_Sense](https://boards.straightdope.com/u/Chessic_Sense)\
**Post date:** [June 25, 2010, 2:30pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/35 "2010-06-25T14:30:54Z")

</div>

I say we start pumping more oil into the Gulf! It’s what they do when California gets set on fire every summer. We should lay down an “escape oil spill”. See, once we’ve pumped so much oil into the Gulf, the oil coming out of the pipe won’t have anywhere to go, so it’ll turn around and go back into the pipe. And then we have no more worries. At all.

But seriously, folks, all these jokes are too clean. I’d expect oil spill jokes to be a bit more…crude?

---

<div class="post-metadata">

**Author:** ![Philster](https://avatars.discourse-cdn.com/v4/letter/p/13edae/32.png) [@Philster](https://boards.straightdope.com/u/Philster)\
**Post date:** [June 25, 2010, 3:57pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/36 "2010-06-25T15:57:36Z")

</div>

Depends…

---

<div class="post-metadata">

**Author:** ![MacTech](https://avatars.discourse-cdn.com/v4/letter/m/c0e974/32.png) [@MacTech](https://boards.straightdope.com/u/MacTech)\
**Post date:** [June 25, 2010, 4:10pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/37 "2010-06-25T16:10:24Z")

</div>

> [@figure9](#):
>
> Sumerian-Cobalt magnets. Shoot them in bunches down the pipe. First they stick to the sides of the pipe then they stick to each other. Problem solved. As a plus all the magnets I’ve torn out of hard-drives become more valuable.

But wouldn’t Mesopotamian-Cobalt magnets work better?

😉

---

<div class="post-metadata">

**Author:** ![JThunder](https://avatars.discourse-cdn.com/v4/letter/j/e95f7d/32.png) [@JThunder](https://boards.straightdope.com/u/JThunder)\
**Post date:** [June 25, 2010, 4:31pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/38 "2010-06-25T16:31:15Z")

</div>

I’d call Aquaman, who would in turn call a couple of great white whales for help. Then when that fails, he’ll use his JLA signal device to call Superman.

---

<div class="post-metadata">

**Author:** ![ivan\_astikov](https://avatars.discourse-cdn.com/v4/letter/i/58f4c7/32.png) [@ivan\_astikov](https://boards.straightdope.com/u/ivan_astikov)\
**Post date:** [June 25, 2010, 7:23pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/39 "2010-06-25T19:23:46Z")

</div>

Where’s Godzilla when you need him?

---

<div class="post-metadata">

**Author:** ![Inigo\_Montoya](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/inigo_montoya/32/124_2.png) [@Inigo\_Montoya](https://boards.straightdope.com/u/Inigo_Montoya)\
**Post date:** [June 25, 2010, 7:39pm UTC](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367/40 "2010-06-25T19:39:58Z")

</div>

What we need is another massive junk shot. Only this time it should be filmed and distributed over the web.

May not stop the oil, but I just wanted to type “junk shot.”

[Previous page](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367.md?page=1)

[Next page](https://boards.straightdope.com/t/how-would-you-stop-the-oil-leak/544367.md?page=3)
