You are usually only making contact at one point, the tip. But… I doubt there’s enough current to damage anything, especially as stainless steel isn’t a super conductor.
I wouldn’t waste my time with something flimsy like a flosser unless i saw a bit piece of fluff it might catch. And I’ve never seen loose fluff. What i see is a shiny smooth interior, maybe with dark patches, because the lint has been jammed down tight by trying to force the connection together. The goal is to scratch the lint enough to loosen it, so it can be fished out.
I’ve never seen this issue on a Kindle, and it might be something else, like a slightly bent connection. And micro USB connections are more fragile, and more prone to that kind of problem than USB C, which was designed in part to be more physically robust.
Mechanical failure is a frequent complaint regarding older charging standards. Micro USB relies on those tiny metal hooks on the connector to keep the cable secure.
Repeated use often causes those hooks to flatten out or the receiving port to widen slightly. A compromised port leads to a loose connection where the cable falls out easily or only charges if you hold it at a precise angle.
The USB-C standard was engineered to withstand significantly more wear and tear. Instead of relying on fragile hooks on the plug, the retention mechanism is housed inside the port and designed to be more robust.
But it’s a really common problem on cell phones that live in linty pockets. In my experience, if you keep a phone long enough, it’s likely to happen. I’ve had about a ⅔ success rate with a needle, and I’ve never left the phone working worse than when i started. I am very nearsighted (with good close up vision) and I’m good with fiddly things, so ymmv.
My (fairly old) phone has a USB-C charging port, and the cable only stays in in one of the two orientations, and even then sometimes needs a wiggle. I put a little dab of wite-out on the plug so I can tell which way is the one that works.
I should maybe try cleaning it out with a pointy tool.
And I don’t, or at least not most of them, plus I don’t have experience or knowledge, so I won’t be trying to replace the port myself.
I tried this, carefully. Concentrating on the corners and keeping away from the contacts. It did seem to help, although it’s not clear how much, but the apparent film of dust appears to be mostly gone. So I scraped the needle up and down the corners, and then hit it with some more compressed air. The plug still wiggles a little in the port, but the little light seems to stay on better, so maybe that’s enough. Time will tell.
It was working, but intermittently and unreliably, and after my previous Oasis refused to respond when it ran completely out of power, I am cautious about not letting that happen again. After using the needle the contact seems more reliable and steady.
The available looseness/movement is side to side, not up and down, so this would, I think, make that worse.
You might not need every conceivable tool. You have to be able to get it open, of course. I have no idea off the top of my head what would be necessary in your specific case for a complete repair. There are guides like this covering specific devices: (you may not need to solder anything, for example)
Yes, I have. USB C intentionally improved on mini/micro USB B. The housings typically mount to the PCB better and the cable/port interconnect is different.
You can feel a difference in physical resistance unplugging a B vs. C. With USB B, there is a tug from the mating hooks on the cable when you unplug. It stresses the port and housing. USB C has the hooks inside the port instead.
Can you make a jock strap for the plug? Wrap a big rubber band around it and then wrap the loop of the rubber band around the Kindle? Just when you’re plugging it in overnight.
I’d try 1) a short extension cable that maybe you can affix semi-permanently and plug into that. Duct tape it in there or something. 2) An angled plug which might have tipping force in a different axis and be more resistant to this problem.
An example of something that might work is one of these.. No-name brand so I can’t vouch for the quality, but it’s a cheap way to attempt.
If you find that the solution to add some support instead works, you can 3d print something pretty easy. Possibly for free at your public library.
If you have a multimeter your could also test to make sure power is 5V and not intermittent, but the leads that come standard with multimeters are almost certainly too small for micro USB.
Edit: I think it’s probably a Micro USB not Mini USB… make sure your designation is right. That Amazon link is here.
This has improved enough that I am okay with it going forward (if it doesn’t get worse). I still have to babysit it a little bit, which means that after plug it in and lay it down, I have to check the little light that it is still charging. I am okay with that, and so far the little light has always been on.