# Making holes in a stainless steel door?

**URL:** <https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517>\
**Category:** Factual Questions\
**Created:** [May 6, 2010, 3:45pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517 "2010-05-06T15:45:00Z")\
**Posts on this page:** 13\
**Page:** 2

<div class="post-metadata">

**Author:** ![billfish678](https://avatars.discourse-cdn.com/v4/letter/b/7bcc69/32.png) [@billfish678](https://boards.straightdope.com/u/billfish678)\
**Post date:** [May 7, 2010, 1:44pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/21 "2010-05-07T13:44:59Z")

</div>

> [@EvilTOJ](#):
>
> When you’re drilling stainless steel, make sure to use some kind of oil on the bit to keep it cool. SS can get work hardened, making it even harder to drill and bits will start breaking. Also don’t go full speed spinning the bit around, go at half speed or lower.
> 
> So essentially, treat it like anal sex; go slow, and use lots of lube 😃

**This for sure**. I didnt know about this and about wore myself out trying to drill a few small holes and hacksaw through some stainless once.

If I can get stainless hot enough to work harden with a hacksaw, I am sure you could do it quite easily with a power saw/drill.

I would literally go only a few seconds at a slow speed and then stop to see how warm the hole saw and stainless is. If its more than barely warm, wait a bit for it to cool before hitting it another few seconds. You DO NOT want to work harden that stainless.

A brand new hole saw, some good cutting oil, and taking it REALLY slow are worth their weight in gold for this DIY operation.

---

<div class="post-metadata">

**Author:** ![Mangetout](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/mangetout/32/19_2.png) [@Mangetout](https://boards.straightdope.com/u/Mangetout)\
**Post date:** [May 7, 2010, 3:09pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/22 "2010-05-07T15:09:23Z")

</div>

Using a holesaw in a handheld power drill, without first making a pilot hole risks several adverse outcomes:

[ul]  
[li]On a metal surface, the possibility that the inbuilt pilot drill will skip or drift[/li][li]Preventing said drift/skip by initially steadying the drill point with your fingertips puts your fingers at risk of injury from the saw parts[/li][li]When the inbuilt pilot breaks through the material, it the sudden give may result in the saw slamming against the workpiece[/li][li]Without a pilot hole, it’s harder to concentrate on keeping the axis of the holesaw perpendicular to the surface, which can cause the saw to bite or bind, which at worst may shear off the pilot drill or skip it out of the hole, sending it skipping over the material, or it may just result in the hole being cut at an angle (even in thin material, this means it’s non-circular)[/li][/ul]

---

<div class="post-metadata">

**Author:** ![Princhester](https://avatars.discourse-cdn.com/v4/letter/p/3e96dc/32.png) [@Princhester](https://boards.straightdope.com/u/Princhester)\
**Post date:** [May 8, 2010, 4:56am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/23 "2010-05-08T04:56:09Z")

</div>

> [@billfish678](#):
>
> **This for sure**. I didnt know about this and about wore myself out trying to drill a few small holes and hacksaw through some stainless once.
> 
> If I can get stainless hot enough to work harden with a hacksaw, I am sure you could do it quite easily with a power saw/drill.
> 
> I would literally go only a few seconds at a slow speed and then stop to see how warm the hole saw and stainless is. If its more than barely warm, wait a bit for it to cool before hitting it another few seconds. You DO NOT want to work harden that stainless.
> 
> A brand new hole saw, some good cutting oil, and taking it REALLY slow are worth their weight in gold for this DIY operation.

I’m not sure about this. I had to drill a large number of holes in stainless a couple of years ago. Many recommended lube, keep cool, go slow to me and it didn’t work really. It worked to some degree but one false move and the stainless just work hardened anyway. Then I found a comment on a website by a guy who had done a lot of stainless drilling and his tip was to do exactly the opposite: no lube, medium speed on a powerful drill (I have a drill press) and be absolutely freakin’ brutal. His theory was that if you make sure the drill is biting deep into fresh steel on each revolution then you won’t get work hardening but if you pussyfoot about then you will.

His theory worked a charm. The only catch was that with a lot of pressure on the drill I snapped off a couple of bits, but then I had over a hundred to do.

---

<div class="post-metadata">

**Author:** ![billfish678](https://avatars.discourse-cdn.com/v4/letter/b/7bcc69/32.png) [@billfish678](https://boards.straightdope.com/u/billfish678)\
**Post date:** [May 8, 2010, 7:59am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/24 "2010-05-08T07:59:31Z")

</div>

> [@Princhester](#):
>
> . His theory was that if you make sure the drill is biting deep into fresh steel on each revolution then you won’t get work hardening but if you pussyfoot about then you will.
> 
> .

Yes.

IFFFFFF when you drill, you have the pressure and speed just so such that nice spiral shavings that look something like fancy pasta noodles are coming out then that theory probably works.

If you don’t get those fancy noodles right off the bat, IMO you better change you game plan fast.

And thats probably only valid for a DRILL bit. I highly suspect you won’t get fancy noodles with a HOLE saw.

FWIW, I am certainly no stainless steel expert. But I can certainly tell you work hardened stainless is a bitch. Its like chipping through a diamond with a toothpick.

Maybe a real expert machinist/stainless dude will chime in here at some point.

Its 3 am and my allergies are killing me so take all this with a barrel of salt.

---

<div class="post-metadata">

**Author:** ![ExTank](https://avatars.discourse-cdn.com/v4/letter/e/35a633/32.png) [@ExTank](https://boards.straightdope.com/u/ExTank)\
**Post date:** [May 8, 2010, 8:14pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/25 "2010-05-08T20:14:12Z")

</div>

If you don’t want to unhinge the door, you’ll want to use something like [this.](http://www.mytoolstore.com/milwauke/4204-1.html) These are typically available at tool-rental companies for reasonable fees. Locally, we rent from K&K Tools when we need stuff like that; the last time I rented a drill press, I got the 1/2" for $60/day, + tax. They also rent/sell bits there, but I won’t cut into hardened metals with used tools.

Use cutting oil, sharp cutting implements, and keep the speed down and the pressure moderate. A good cut will deliver a long “corkscrew” shaped metal wire.

Do NOT use a hole saw to cut through hardened metal; use drill bits, and work up from a small pilot hole to the desired size. Do NOT get impatient and jump up in drill size too quickly; you just get broken drill bits.

ETA: wear appropriate clothing and eye protection: that wire/ribbon is _sharp!_

---

<div class="post-metadata">

**Author:** ![Apocalypso](https://avatars.discourse-cdn.com/v4/letter/a/f19dbf/32.png) [@Apocalypso](https://boards.straightdope.com/u/Apocalypso)\
**Post date:** [May 9, 2010, 1:02am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/26 "2010-05-09T01:02:56Z")

</div>

I lived in an apartment once where someone botched a deadbolt installation. Dunno if it was the landlord or a previous tenant, but the hole wasn’t drilled perfectly straight. I put in a new deadbolt (not knowing the problem was the hole), still didn’t work right.

If you don’t know what you’re doing, ask a professional or someone that has experience installing locks/deadbolts. If you screw it up, your door is ruined and your deadbolt won’t work right.

---

<div class="post-metadata">

**Author:** ![billfish678](https://avatars.discourse-cdn.com/v4/letter/b/7bcc69/32.png) [@billfish678](https://boards.straightdope.com/u/billfish678)\
**Post date:** [May 9, 2010, 2:41pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/27 "2010-05-09T14:41:22Z")

</div>

> [@Apocalypso](#):
>
> If you don’t know what you’re doing, ask a professional or someone that has experience installing locks/deadbolts. If you screw it up, your door is ruined and your deadbolt won’t work right.

Good point. New doors, particularly good one are not cheap. At the very least get some advice from someone who knows how to do it and be careful if you do it yourself.

---

<div class="post-metadata">

**Author:** ![Mangetout](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/mangetout/32/19_2.png) [@Mangetout](https://boards.straightdope.com/u/Mangetout)\
**Post date:** [May 9, 2010, 3:36pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/28 "2010-05-09T15:36:27Z")

</div>

If it were me, I’d remove the door and take it somewhere they could cut the hole with a water jet cutter.

---

<div class="post-metadata">

**Author:** ![johnpost](https://avatars.discourse-cdn.com/v4/letter/j/f17d59/32.png) [@johnpost](https://boards.straightdope.com/u/johnpost)\
**Post date:** [May 9, 2010, 3:44pm UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/29 "2010-05-09T15:44:24Z")

</div>

filmyak knows what he’s doing he is hiring a professional.

---

<div class="post-metadata">

**Author:** ![CBEscapee](https://avatars.discourse-cdn.com/v4/letter/c/b19c9b/32.png) [@CBEscapee](https://boards.straightdope.com/u/CBEscapee)\
**Post date:** [May 11, 2010, 2:52am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/30 "2010-05-11T02:52:12Z")

</div>

Locksmiths or carpenters that specialize in hanging doors use a jig that clamps to the door and guides the bits for drilling.

I custom build doors and install them. I own this jig:  
[http://www.templaco.com/html/product.asp?id=225&mode=Bore\_Master\_Kits](http://www.templaco.com/html/product.asp?id=225&mode=Bore_Master_Kits)  
For metal doors an adapter for a pilot hole is used to bore from both sides before removing the jig to finish drilling the hole with the proper hole saw.

---

<div class="post-metadata">

**Author:** ![crowmanyclouds](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/crowmanyclouds/32/19884_2.png) [@crowmanyclouds](https://boards.straightdope.com/u/crowmanyclouds)\
**Post date:** [May 11, 2010, 3:33am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/31 "2010-05-11T03:33:35Z")

</div>

[drilling hardened steel]  
[These](http://www.drillbitsworld.com/Straight_Flute-Fractional_Sizes.html), straight flute solid carbide bits will go through up to Rc 60 hardened steel (they do need the right speed and lube!).  
[/drilling hardened steel]

CMC fnord!

---

<div class="post-metadata">

**Author:** ![Crawlspace](https://avatars.discourse-cdn.com/v4/letter/c/d6d6ee/32.png) [@Crawlspace](https://boards.straightdope.com/u/Crawlspace)\
**Post date:** [May 18, 2010, 6:30am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/32 "2010-05-18T06:30:02Z")

</div>

> [@DCnDC](#):
>
> Yes a hole saw will have an arbor bit, but that’s not the point. Have you ever used a hole saw on a metal door? Without a pilot hole the saw teeth will stick and it will jump, leaving horrible looking spiral scratches on the door that are impossible to fix.

Yes. More times than you can imagine. My father is a contractor and I started working on construction sites when I was 4 (sweeping). A good hole saw will have 1/2"-1" of pilot bite into the material. That’s more than enough to center the drill. Spiral scratch marks are caused by weak wrists and jumping is caused by forcing the drill too much. Neither problem is solved by drilling a pilot hole.

---

<div class="post-metadata">

**Author:** ![Bryan\_Ekers](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/bryan_ekers/32/183_2.png) [@Bryan\_Ekers](https://boards.straightdope.com/u/Bryan_Ekers)\
**Post date:** [May 18, 2010, 6:49am UTC](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517/33 "2010-05-18T06:49:33Z")

</div>

Get a Desert Eagle, shoot a hole in the damn door. Power tools are robbing us of our manhood!

[Previous page](https://boards.straightdope.com/t/making-holes-in-a-stainless-steel-door/538517.md?page=1)
