# Propane  Question

**URL:** <https://boards.straightdope.com/t/propane-question/525904>\
**Category:** Factual Questions\
**Created:** [January 21, 2010, 10:07pm UTC](https://boards.straightdope.com/t/propane-question/525904 "2010-01-21T22:07:02Z")\
**Posts on this page:** 1\
**Page:** 1

<div class="post-metadata">

**Author:** ![Gbro](https://avatars.discourse-cdn.com/v4/letter/g/c6cbf5/32.png) [@Gbro](https://boards.straightdope.com/u/Gbro)\
**Post date:** [January 21, 2010, 10:07pm UTC](https://boards.straightdope.com/t/propane-question/525904/1 "2010-01-21T22:07:02Z")

</div>

I would very much appreciate input to a puzzling propane situation I had recently.

Background;  
One of my many 20 lbs. propane cylinders was used on 2 different heating devices this past month.  
One is a tank top heater that we more commonly refer to as a [sunflower heater](http://www.gasheaterstore.com/Mr-Heater-MH12CS-8000--14000-Btu-Propane-Single-Cooker-Propane-Heater-With-Electronic-Ignition_p_74.html).  
The other is a [Mr Heater Buddy Heater.](http://www.gasheaterstore.com/Mr-Heater-MH9BX-9000-Btu-Buddy-Indoor-Safe-Portable-Propane-Heater_p_9.html) Both heaters were used with a [12 ft. assessory hose.](http://www.gasheaterstore.com/Mr-Heater-F273702-12-ft-Hose-With-Hand-Wheel-For-Inside-Thread-40Old-Design-Tanks41--for-MH9B-only_p_307.html).  
The 20 lbs cylinder was used approximately 8 hours with these 2 heater and the ambient temp. was in the mid 20 (f) both times.  
I set up the buddy heater last Monday and and it was also in the mid 20’s (temp) and upon igniting the stove it would not stay lit. I assessed the cylinder and the weight indicated there was plenty of fuel remaining in it. I tried to lite the heater with a burns-o-matic torch and I had no luck getting stove to light. I then assumed the stove was malfunctioning.  
Then on Tuesday I rapidly packed the Grandsons into truck for another evening of ice fishing and had intended to bring along the other stove(sunflower). I attempted to again light the Buddy heater and after several min. drove back home and attached the sunflower heater to the 12’ assessory hose. I then attempted to test light the stove in the garage. I could not light this stove even though I had what sounded like plenty of fuel flowing through the venturi. I then used the burns-o-matic torch and having again what sounded like plenty of fuel flowing I could not ignite any fuel. I had the thermocouple heated up with the hand held torch so that I didn’t have to hold the bypass open. After several attempts at igniting , and checking to make sure i wasn’t creating a danger to myself and the garage with gas buildup, The heater then lit!. I shut it down and then re-lit the stove with the regular igniter and the stove lit just like it should have. I then re-attached the Buddy Heater and the pilot ignited 1st push on the igniter and burned properly the rest of the night.🙂

Now my question is why did this stove work 8+ hours on this cylinder and then dispense a gas that would not light and then after 2 days of fiddling again dispense a flammable gas???:dubious: I probably purged this tank through my stove for about 10 min. before flammable fuel again dispensed.  
I do know that cylinders I own were originally purged, however after researching this problem I find that the purging to my cylinders were not done exactly as what is[recommended here;](http://home.earthlink.net/~derekgore/rvroadiervfulltimingwhatisitreallylike/id45.html) and other sites I found using ask dot com. (The purging was done with liquid not vapor).  
I have to think I had air in this cylinder and for some reason the air was layered in the cylinder OR There is a remote possibility someone did a tank switch on me when they couldn’t get it to work for them:dubious::dubious: I do not have my name on all my cylinders YET!  
The majority of the information I have found says I would probably have a poor mix of fuel resulting in poor performance with air in the cylinder to being unable to run device.
