# Superglue: re-gluing **URL:** \ **Category:** Factual Questions\ **Created:** [April 10, 2019, 2:22pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333 "2019-04-10T14:22:18Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![Johnny\_L.A](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/johnny_l.a/32/1084_2.png) [@Johnny\_L.A](https://boards.straightdope.com/u/Johnny_L.A)\ **Post date:** [April 10, 2019, 2:22pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/1 "2019-04-10T14:22:18Z")
The faceplate on my Seconic L-398 light meter is held onto the head by two screws that screw into threaded brass mounting posts inside of the head. The posts appear to be superglued to the plate they’re on. I managed to break one off. How do I re-attach the post? Can I just put a drop of cyanoacrylate on it? Or do I need to use acetone (nail polish remover) to clean the bottom of the post and the spot where it attaches before applying the glue? ---
**Author:** ![beowulff](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/beowulff/32/542_2.png) [@beowulff](https://boards.straightdope.com/u/beowulff)\ **Post date:** [April 10, 2019, 2:39pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/2 "2019-04-10T14:39:30Z")
I’d clean the post, and then carefully roughen the area on the plate where the post sits, using an x-acto blade. Then, I’d use epoxy, not superglue. ---
**Author:** ![Johnny\_L.A](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/johnny_l.a/32/1084_2.png) [@Johnny\_L.A](https://boards.straightdope.com/u/Johnny_L.A)\ **Post date:** [April 10, 2019, 2:56pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/3 "2019-04-10T14:56:28Z")
> [@beowulff](#): > > I’d clean the post, and then carefully roughen the area on the plate where the post sits, using an x-acto blade. > Then, I’d use epoxy, not superglue. I was under the impression that cyanoacrylate works best on a smooth surface. (Not that I’ve spent much time thinking about it.) I might have some epoxy around here. I didn’t think of it because of the way it appears to have originally been attached. ---
**Author:** ![beowulff](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/beowulff/32/542_2.png) [@beowulff](https://boards.straightdope.com/u/beowulff)\ **Post date:** [April 10, 2019, 3:41pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/4 "2019-04-10T15:41:04Z")
> [@Johnny\_L.A](#): > > I was under the impression that cyanoacrylate works best on a smooth surface. (Not that I’ve spent much time thinking about it.) > > I might have some epoxy around here. I didn’t think of it because of the way it appears to have originally been attached. I find “Supergules” to be too brittle. They also don’t adhere to all plastics. Also, if the plastic is clear, they can fog it. That said, if it’s not under a lot of stress, Superglue is probably fine. ---
**Author:** ![Johnny\_L.A](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/johnny_l.a/32/1084_2.png) [@Johnny\_L.A](https://boards.straightdope.com/u/Johnny_L.A)\ **Post date:** [April 10, 2019, 4:54pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/5 "2019-04-10T16:54:18Z")
> [@beowulff](#): > > That said, if it’s not under a lot of stress, Superglue is probably fine. It broke off because I overtightened the screw and wrenched it off. That said, there are millions of these things out there, and it’s the first time I’ve heard of it happening. As long as I don’t overtighten the screw, and if I’m careful not to drop it on its head, I don’t see why it shouldn’t be ‘as good as new’. Assuming I do decide to go the superglue route, would I need to clean both surfaces off with acetone? ---
**Author:** ![beowulff](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/beowulff/32/542_2.png) [@beowulff](https://boards.straightdope.com/u/beowulff)\ **Post date:** [April 10, 2019, 6:17pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/6 "2019-04-10T18:17:51Z")
I’d be worried about the acetone crazing the plastic. So, I’d just scrape the area and be done with it. ---
**Author:** ![Johnny\_L.A](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/johnny_l.a/32/1084_2.png) [@Johnny\_L.A](https://boards.straightdope.com/u/Johnny_L.A)\ **Post date:** [April 10, 2019, 7:44pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/7 "2019-04-10T19:44:39Z")
I tried the cyanoacrylate. I decided to use the screw on the other side. It came off. I’ve applied the superglue to that one now. If the posts come off again, I’ll clean the area with acetone and apply epoxy. ---
**Author:** ![Dandan](https://avatars.discourse-cdn.com/v4/letter/d/a87d85/32.png) [@Dandan](https://boards.straightdope.com/u/Dandan)\ **Post date:** [April 11, 2019, 12:19pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/8 "2019-04-11T12:19:02Z")
Acetone is used to melt/weld certain plastics together; think of a plexiglas display case. Alcohol will clean contaminants off without damage. Dan ---
**Author:** ![Johnny\_L.A](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/johnny_l.a/32/1084_2.png) [@Johnny\_L.A](https://boards.straightdope.com/u/Johnny_L.A)\ **Post date:** [April 11, 2019, 5:23pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/9 "2019-04-11T17:23:29Z")
> [@Dandan](#): > > Acetone is used to melt/weld certain plastics together; think of a plexiglas display case. Alcohol will clean contaminants off without damage. Good to know. (I think the light meter’s case is ABS plastic.) ---
**Author:** ![TriPolar](https://sea3.discourse-cdn.com/straightdope/user_avatar/boards.straightdope.com/tripolar/32/3008_2.png) [@TriPolar](https://boards.straightdope.com/u/TriPolar)\ **Post date:** [April 11, 2019, 5:41pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/10 "2019-04-11T17:41:12Z")
Acetone readily dissolves polystyrene foam, like foam peanuts, molded packing material, and insulation. Other forms of it like ABS (Acrylonitrile Butadiene Styrene) don’t dissolve as readily but acetone can be used to ‘weld’ it together. Generally avoid using acetone on unknown plastics, and pretty much anything that smells like acetone also. ---
**Author:** ![doubleminus](https://avatars.discourse-cdn.com/v4/letter/d/5daacb/32.png) [@doubleminus](https://boards.straightdope.com/u/doubleminus)\ **Post date:** [April 11, 2019, 9:03pm UTC](https://boards.straightdope.com/t/superglue-re-gluing/832333/11 "2019-04-11T21:03:42Z")
You can use baking soda powder to instantly solidify cyanoacrylate and to fill gaps. You can sprinkle a bit of soda before affixing the parts, apply superglue and sprinkle again to solidify and fill gaps. You can brush the extra powder away. While it looks completely solid after applying the baking soda, maximum strength is achieved after a few hours. I found this to be better than epoxy in many cases, especially plastics which are slightly dissolved by cyanoacrylate. \*Baking soda = Sodium Bicarbonate